How To Clean A Dyson So It Really Sucks

Is your Dyson not sucking as well as it used to? Find out how to clean a Dyson so it really sucks. It’s easy to clean Dyson vacuum.

Has your Dyson really started sucking? 😉 Maybe your vacuum is so dirty you don’t feel like it has the same sucking power it had when you first bought it. Giving your vacuum a good cleaning will help make a major difference in how well it cleans.

I started to notice my Dyson wasn’t working as well about two years after I bought it. I had washed the filters plenty of times, but still didn’t feel like that made a difference.

Finally, I got brave and took that puppy apart to clean it. I got tired of my Dyson not sucking and gave it a deep clean.

While all models of Dyson vacuums are a little different, most of the components are the same.

Some recommend cleaning with products, but today I am going to show you how to make your Dyson shine using only a towel and water!

Once you are finished, you can see how I clean our dry vent, the easiest way to clean a front load washer, and my genius trick for cleaning blinds!

Table of contents

What You’ll Need

• Microfiber towel (these cloths from Amazon are my favorites!)
• Water
• New filter – depending on the condition you may or may not need to replace the filter. (I just grab mine from Amazon)

How to Clean a Dyson Vacuum Step by Step

Step 1: Start by removing the bin from the vacuum. You will want to empty the bin in a trash can before you start to clean it.

Step 2: Then take the bin to a sink. I recommend using a laundry sink if you have it. It can be a very dirty job, so I like to contain the mess to my already dirty laundry room. On the back part of the bin will be a small button that you can use to remove the clear part of the bin.

Step 3: Run water into the clear part to remove any dirt or grime. You can scrub with a microfiber cloth if you need to. Once clean, set it to the side.

Free Weekly Cleaning Printable

Clean your home in under 30 minutes a day with this free Weekly Cleaning printable!

Step 4: Next, you will want to remove the filter from the vacuum. Just pull up on the section labeled filter.

Step 5:Remove the filter from the unit. The filter will have two sections. There is the yellow and white section and a blue foamy section.

Step 6: Wash both of them out well. You can squeeze the water out of the blue foam and set both to the side. If the blue foam section is looking very worn, you can purchase more here. I usually replace mine about every 6 months.

Step 7: Now on to the dirtiest part of the Dyson. This one is caked with dirt and grime. It’s no wonder that it isn’t sucking well. I use the spray hose from my sink and just blast it with water. Spray from all sides until the water is running clear.

Step 8: Once the water is running clear you can move on to the inside of the bin. Mine is always caked with tons of dirt and dust.

Again, I just use the sprayer until the water runs clear.

Step 9: Once you are done cleaning the Dyson vacuum set out a large towel or blanket in a sunny area and allow the parts to completely dry. This usually takes most of a day.

Step 10: When the parts are all dry you can reassemble them and get back to vacuuming.

Deep Cleaning a Dyson

Maybe your vacuum is past the point of just needing the filter and canister cleaned out. Use these other tips to deep clean your Dyson so it’s like brand new again!

Brush Bar – If your bar has a ton of hair and debris built up, it’s time to take care of it. Gently cut the hair off the roller using scissors. Different models may have a soleplate that needs to be removed to reach the roller. If the plate needs removing you will have to use a flathead screwdriver.

Brush compartment – Use the damp microfiber to wipe out the area where the roller sits.

Hose – Sometimes you may have a small blockage, but it’s easy to clean. Take the hose off and dump any debris in the trash. If you know there is a blockage but cannot see it, run warm water through the hose until it’s dislodged. Allow the hose to dry completely on its own before reassembling.

Attachments – These little pieces get dirty too! Simply wipe those with a towel and allow them to dry.

Helpful Tips

• Allow the parts (including the filter) to dry naturally. Never place them in the dryer, dishwasher (to wash and dry), or the microwave.
• Leftover moisture in any of the parts could cause harm to the motor.
• Avoid washing any of the cyclones with water.
• Regular maintenance of your Dyson will extend it’s life, cut down on the need of replacement filters, and reduce clogs and blockages.
• If you have a newer Dyson vacuum cleaner, we recommend reading over the manufacturer’s guide so you understand all the parts, what the warranty covers, and if there are any special notes about your model.

Common FAQs

We recommend swapping them out every 6 months, but at a minimum 1 time per year. If you are vacuuming finer dust, they will need cleaning more often.

Absolutely! The only exception is too use water only. Avoid using any type of detergents or vinegar.

It doesn’t take much time to really clean your vacuum. Now that you know how to clean a Dyson you can clean it every 6 months or so. With just a small amount of work, you can notice a huge difference in the cleaning power of your Dyson. Your vacuum can stop sucking and really start sucking up dirt.

Free Weekly Cleaning Checklist

Clean your home in under 30 minutes a day with this free weekly cleaning printable