How to Remove Fiberglass from Arms & Hands

How to Remove Fiberglass from Arms & Hands

Fiberglass is a manmade product, in use since the 1930s for filtration and insulation. In modern times, shower stalls, bathtubs, kayaks, boat hulls and many other objects contain fiberglass. When you saw, trim, or handle fiberglass, small fibers work their way into the skin of your hands and arms, creating an irritating itch.

If you are experiencing serious medical symptoms, seek emergency treatment immediately.

Steam Shower

Disrobe carefully, taking care not to drag your shirt over your arms or hands. Pressure on the skin can drive the fiberglass splinters deeper into your skin, making removal much more difficult.

How to Remove Fiberglass From Hands and Fingers

Learn More

Enter your shower and turn on the hot water and a small amount of cold water. Stand away from the water stream for several minutes. The goal is to work up steam in the enclosed space without getting your hands or arms wet. The steam opens your pores and increases the chances of the splinters falling out.

Adjust the water to a comfortable temperature and step back into the stream. Allow the water to run off of your arms and hands. If any of the splinters were loosened as a result of the steam, this step will rinse them away.

How to Care for an Embedded or Impaled Object in the Skin

Learn More

Add natural soap to a non-coarse loofah and gently brush the skin on your hands and arms. Do not apply pressure, as doing so will drive any remaining splinters deeper. Rinse your hands and arms with water to remove the soap.

Turn off the water and dry your hands and arms by lightly pressing the towel against the skin. Do not drag the towel.

Put on a loose-fitting, sleeveless shirt. If you are still experiencing irritation, move on to the next section.

• Disrobe carefully, taking care not to drag your shirt over your arms or hands.
• Add natural soap to a non-coarse loofah and gently brush the skin on your hands and arms.

Baking Soda Paste

Add 1/2 cup of baking soda to a bowl.

Add a small amount of water. Mix the baking soda and water into a paste with your fingers. If the paste is too dry and powdery, add more water. If the paste is too soupy, add more baking soda.

Dress any itchy areas on your hands or arms with the paste.

Allow the paste to dry for 25 to 30 minutes. Try not to move your hands or twist your wrist while the paste dries. The powder will harden around the exposed sections of the fiberglass splinters 23.

Rinse the dried baking soda off of your skin. Any fiberglass splinters that became attached to the paste will pull out and rinse away.

Tips

Remove your clothing and hose off your arms and hands immediately after working with fiberglass to avoid irritation in the future.

Powder your skin before working with fiberglass. The powder may block fibers from entering your skin.

Warnings

If you have fiberglass on your hands, do not touch your nose, mouth, ears or eyes.

• Add 1/2 cup of baking soda to a bowl.
• Mix the baking soda and water into a paste with your fingers.

Related Articles

How to Remove Fiberglass From Hands and Fingers

Learn More

How to Care for an Embedded or Impaled Object in the Skin

Learn More

How to Treat Cracked Skin on the Hands

Learn More

How to Freshen Sweaters

Learn More

How to Clean High School Jacket Vinyl Sleeves

Learn More

Treatments for Blocked Sweat Glands

Learn More

How to Empty the Fluid in a Bic Lighter

Learn More

How to Get Rid of Deep Clogged Pores

Learn More

How to Break in a Stetson Hat

Learn More

What Happens if Silica Gel Is Ingested?

Learn More

References

Resources

Writer Bio

Aaron Kopf graduated from the University of Central Arkansas with honors in 2009, holding a Bachelor of Arts in communication. While enjoying his time at college, Kopf was published in The Echo and Vortex magazine.