You are viewing the article How to Sharpen Trimmer Blades at Lassho.edu.vn you can quickly access the necessary information in the table of contents of the article below.
X
This article was co-written by Laura Martin. Laura Martin is a licensed esthetician in Georgia. She has been a hair stylist since 2007 and a cosmetology teacher since 2013.
This article has been viewed 5,562 times.
Most trimmers have a self-sharpening feature to keep the cutting head sharp, however, blades can wear out quickly if not cleaned and oiled periodically. In order to limit the condition of uneven, messy and kinky hair, you should sharpen the blade every time you feel that the trimmer is not smooth. Please clean the blade first to remove hair debris and rust, otherwise the effect will not be as expected.
Steps
Cleaning the trimmer
{“smallUrl”:”https://www.wikihow.com/images_en/thumb/d/df/Sharpen-Hair-Clippers-Step-1-Version-5.jpg/v4-460px-Sharpen-Hair-Clippers- Step-1-Version-5.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/d/df/Sharpen-Hair-Clippers-Step-1-Version-5.jpg/ v4-728px-Sharpen-Hair-Clippers-Step-1-Version-5.jpg”,”smallWidth”:460,”smallHeight”:259,”bigWidth”:728,”bigHeight”:410,”licensing”:” <div class=”mw-parser-output”></div>”}
Screw on the blade. Find and tighten the screw that secures the blade to the trimmer. Most new trimmers will have 2 screws located on the bottom edge of the blade. After tightening these 2 screws, gently remove the blade and fixings (if any).
- If the bottom edge of the blade does not pop out easily, use tweezers to pull the blade out from below.
- Make a note of where and how to install the blades and components so that they don’t have to be difficult to put them back together.
Brush off hair and dirt. Cleaning the trimmer will help you use it more smoothly, and the blade can be sharpened evenly and without entanglement. Use a wire brush, steel wool, or an old toothbrush to remove hair stuck in the blade. [1] X Research Source
Clean rust with razor blade cleaner. If the razor blade is rusty or still has impurities after brushing, you can use a razor blade cleaner or other specialized product to deal with it. Place the blade in a small bowl of the solution and soak for a few minutes, or dip a cotton ball in the solution and wipe the blade to remove any accumulated rust.
- Some people say they have successfully removed rust with rubbing alcohol, but you may need to use a strong 90% alcohol solution. [2] X Research Source Lower concentrations of rubbing alcohol may not be as effective.
Dry the blade. Dry the entire blade with a clean towel to remove any remaining hair and dirt. If there is still residue on the blade, use the cleaning solution again.
- If rust stains remain after cleaning, you should replace the blade.
{“smallUrl”:”https://www.wikihow.com/images_en/thumb/7/7e/Sharpen-Hair-Clippers-Step-5-Version-4.jpg/v4-460px-Sharpen-Hair-Clippers- Step-5-Version-4.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/7/7e/Sharpen-Hair-Clippers-Step-5-Version-4.jpg/ v4-728px-Sharpen-Hair-Clippers-Step-5-Version-4.jpg”,”smallWidth”:460,”smallHeight”:259,”bigWidth”:728,”bigHeight”:410,”licensing”:” <div class=”mw-parser-output”></div>”}
Check the blade (optional). After cleaning, it is likely that the trimmer will work smoothly again, especially for the model with the self-sharpening feature. Reassemble the trimmer, turn it on for a few minutes to make the parts fit together and then try it on your hair. If the trimmer is still not sharp or the cut is uneven, move on to the blade sharpening steps in the next section.
- For optimal results, it is recommended that you apply a few drops of trimmer oil before test cutting. (This is recommended every 2-3 uses.)
Sharpen the trimmer blade
{“smallUrl”:”https://www.wikihow.com/images_en/thumb/1/18/Sharpen-Hair-Clippers-Step-6-Version-4.jpg/v4-460px-Sharpen-Hair-Clippers- Step-6-Version-4.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/1/18/Sharpen-Hair-Clippers-Step-6-Version-4.jpg/ v4-728px-Sharpen-Hair-Clippers-Step-6-Version-4.jpg”,”smallWidth”:460,”smallHeight”:259,”bigWidth”:728,”bigHeight”:410,”licensing”:” <div class=”mw-parser-output”></div>”}
Use a magnetic holder to hold the blade (optional). Place the lower edge of the blade into the opening of the magnet holder so that the blade part is protruding. This will make it easier for you to sharpen without cutting your hand or dropping the blade.
- Strong and flat magnets are also suitable. If using this magnet, proceed with caution so that the blade does not fall off the suction surface and injure you.
- Sharpen both blade edges following the steps below, one at a time.
Run the blade along the edge of the coarse grindstone. You can buy rough grinding stones at any electrical – water – home appliance store. Using a 4000-grit whetstone, tilt the blade at an angle of 30-45º and brush it vertically on the rough surface 5-10 times until the blade is shiny and even. Use a dry cloth to clean the metal debris on the sharpening stone and blade. [3] X Research Source Then rotate the blade and sharpen the remaining edge.
- With ceramic blade trimmer , you need to use diamond sharpening stone. Read the product label carefully so as not to confuse a ceramic whetstone with a ceramic grindable stone.
Repeat the process with the sharpening stone (optional). Now the blade looks pretty even, but if you want to make the edge sharper and smoother, you can continue the same steps with an 8000 grit fine grindstone. As before, run each edge of the blade along the stone surface in one direction about 5-10 times and then wipe it off with a dry towel.
Reinstall the trimmer. Check to make sure that you install the blade in the correct position, distance and orientation. Then tighten the screw to secure the blade.
Lubricate the trimmer. This step is recommended every 2-3 uses, especially after the blade has just been sharpened. Add a few drops of oil to the blade to limit wear due to friction and overheating.
- If you don’t have a special trimmer oil, you can use something that’s light and penetrating. Avoid using heavy and dark oils as there is a chance of clogging the blade. [4] X Research Source Before oiling a trimmer for the first time, you should consult your barber or research online to choose the right one.
Turn on the trimmer for a few minutes. Turn on the trimmer so that the blade and parts rub together for a few minutes. This process will give the blade a little more sharpening. Then you can start using it on your hair. Hopefully at this point you will be satisfied with the smooth and sharp cuts.
Advice
- There are many different sharpening products, including those specifically for trimmer blades. An inexpensive double-sided sharpening stone is enough for home use, but if you need to sharpen the trimmer frequently, other specialized products will be more appropriate.
- You can also send the blade to your local professional sharpener/trimmer manufacturer or by mail.
- A good tip for cleaning hair and other debris is to turn on the trimmer and dip the blade in a specialized cleaning solution (like Varsp). Run the trimmer for a few seconds to remove dirt and lubricate the blade.
- Ceramic trimmer blades don’t need to be sharpened as often, but they are quite brittle and break easily if tightened too tightly, or when used on thick and tangled hair. [5] X Research Sources
Warning
- If it is only used to cut hair, the blade will take longer to become blunt than if you regularly use a trimmer to cut animal hair.
- Do not forget that the blade after sharpening is very sharp and can injure you. Use caution when reinstalling the trimmer.
Things you need
- Screwdriver
- Iron brush, toothbrush or steel wool
- Razor blade cleaning products or rubbing alcohol
- Cotton balls or small bowls
- Trimmer oil
- Towel
- Tweezers (optional)
X
This article was co-written by Laura Martin. Laura Martin is a licensed esthetician in Georgia. She has been a hair stylist since 2007 and a cosmetology teacher since 2013.
This article has been viewed 5,562 times.
Most trimmers have a self-sharpening feature to keep the cutting head sharp, however, blades can wear out quickly if not cleaned and oiled periodically. In order to limit the condition of uneven, messy and kinky hair, you should sharpen the blade every time you feel that the trimmer is not smooth. Please clean the blade first to remove hair debris and rust, otherwise the effect will not be as expected.
Thank you for reading this post How to Sharpen Trimmer Blades at Lassho.edu.vn You can comment, see more related articles below and hope to help you with interesting information.
Related Search: