You are viewing the article How to Click Rj45 . Network Cable at Lassho.edu.vn you can quickly access the necessary information in the table of contents of the article below.
This article was co-written by Ricardo Mitchell. Ricardo Mitchell is general manager of CN Coterie, an EPA-certified construction company based in Manhattan, New York. CN Coterie specializes in home improvement, electrical, plumbing, carpentry, furniture restoration, dismantling of OATH/ECB violators, and dismantling of DOB violators. Ricardo has more than 10 years of experience in the electrical and construction industry, his associates have more than 30 years of experience in the related industry.
There are 9 references cited in this article that you can view at the bottom of the page.
This article has been viewed 2,525 times.
You can quickly press the network cable into the RJ-45 connector (also known as the network nut) with or without cos clamps. If you have a cos plier, strip off part of the cable sheath, untwist the ends, and arrange the wires in a certain order, insert them into the lattice and then press the pins into the wire with the presser part of the cos. power to fix the connector. If you don’t have cos pliers, no problem! You can use scissors or a paper cutter to cut off part of the sheath at the end of the cable, remove the twisted ends and arrange the wire sets in a certain order, insert them into the RJ-45 lattice and then use a small flathead screwdriver to push down each pin in the connector.
Steps
Use cos . pliers
- The wire stripper is a round hole located near the handle of the tool.
- The cable sheath needs to be neatly peeled off to reveal the wires inside.
- Cut the sheath or the plastic core that separates the wires to separate the wires.
- Do not cut any fibers in the cable, or you will not be able to press them into the network bead.
- There are a total of 8 wires that need to be arranged in the correct order above.
- Note: wires with a slash symbol (e.g. Orange/White or Brown/White) refer to two colors on the same small wire.
- The cutting part of the tool looks similar to the jaws of a wire cutter.
- The ends of the wire must be equal to be able to be clicked on the RJ-45 network bead properly. If you cut unevenly, move the pliers down a little more and cut again.
Tip: If the tool does not have a cutter, you can use wire cutters or scissors.
- The end of the cable cover should just go through the base of the network particle a little.
- If there are any small wires that are bent or aren’t plugged into the slot properly, you’ll need to unplug the cables, straighten the wires with your fingers, and then try again.
- The wires must be plugged in in the correct order, and each end must be in the slot before you can press the network beads.
- The cos pliers will press the contact pins in the slot to the end of the power cord to fix and connect the RJ-45 network cable.
- If there are any contact pins that have not been pressed down, put the web bead back into the cos clamp and press it again.
Connecting RJ-45 network beads without cos . pliers
- Do not cut too deep when starting out.
Tip: If you don’t have scissors, you can use a paper cutter to cut the cable’s sheath. However, be careful not to cut the wires inside.
- Some wires will have 2 colors, such as Orange/White wire.
- The ends of the wire need to be equal to be able to plug into the 8 slots in the network seed.
- If you make an uneven cut, move the chain scissors down a bit and cut back in a straight line.
- Take care not to crack or break the plastic web bead.
- Shake the cable gently to see if there is a “click” sound indicating that one of the contact pins is not fixed.
Things you need
Use cos . pliers
- Versatile cos pliers
- RJ-45 . Connector
Connecting RJ-45 network beads when there is no cos . pliers
- RJ-45 . Connector
- Drag
- Screwdriver with flat and thin tip
This article was co-written by Ricardo Mitchell. Ricardo Mitchell is general manager of CN Coterie, an EPA-certified construction company based in Manhattan, New York. CN Coterie specializes in home improvement, electrical, plumbing, carpentry, furniture restoration, dismantling of OATH/ECB violators, and dismantling of DOB violators. Ricardo has more than 10 years of experience in the electrical and construction industry, his associates have more than 30 years of experience in the related industry.
There are 9 references cited in this article that you can view at the bottom of the page.
This article has been viewed 2,525 times.
You can quickly press the network cable into the RJ-45 connector (also known as the network nut) with or without cos clamps. If you have a cos plier, strip off part of the cable sheath, untwist the ends, and arrange the wires in a certain order, insert them into the lattice and then press the pins into the wire with the presser part of the cos. power to fix the connector. If you don’t have cos pliers, no problem! You can use scissors or a paper cutter to cut off part of the sheath at the end of the cable, remove the twisted ends and arrange the wire sets in a certain order, insert them into the RJ-45 lattice and then use a small flathead screwdriver to push down each pin in the connector.
Thank you for reading this post How to Click Rj45 . Network Cable at Lassho.edu.vn You can comment, see more related articles below and hope to help you with interesting information.
Related Search: